How to replace the back cover of a Samsung Galaxy S6 Edge. How to open the back cover of a Samsung phone How to open the cover of Galaxy C6

Let's find out in what ways you can open the back cover of your Samsung mobile phone. No one mobile phone is not complete without a SIM card. This is a small chip that provides us with services cellular... In some Samsung models it is necessary to remove the panel to gain access to the cell where the chip is inserted. And also Micro-SD - a flash drive for mobile device... Or get to the motherboard for repair.

The way to remove the cover on the Samsung J5 phone

V Lately developers of mobile phones of different brands began to create cases in which the back cover is simply absent. In fact, it is, but ordinary users it is not possible to open it without special devices. So, for example, the two constituent parts Samsung cases J5 glued together. And in order to glue them, the case must be exposed to heating at a temperature of 100 degrees. This will require hot air gun.

Warming up the case with a hot air gun

Before opening the case, be sure to remove the cells for the SIM card and flash drive.

The muzzle of the hot air gun must be directed towards the back of the Samsung and its seams. Then you need to arm yourself with a plastic card or a plastic scalpel to pry the front screen module.

Use a plastic card to pry off the case seams

The lid is not a thin plastic sheet, as in classic smartphones, but rather a depression in the form of a bath. You should be very careful when working along the seam of your phone with a card. Don't run it too deep. 0.5 cm is enough. Be careful not to damage important modules of the phone.

Use plastic card to open Samsung case

When the lid yields, do not rush to open the case completely, do it with caution. After all, both parts exchange information using a wide ribbon cable that connects the screen module and the Samsung motherboard.

Screen module flex cable in Samsung

To disconnect the ribbon cable, you need to open the mount cover and remove the ribbon cable from the socket. It's pretty simple. The main thing is not to rush and be attentive.

How to open the back cover on Samsung Galaxy S7 Edge

Let's look at an example of how to open non-removable back covers on the Galaxy smartphone S7 Edge specialists. It is much easier to do this when you have special equipment at hand. It resembles an ordinary vise equipped with a large suction cup.

Cover opener on a Samsung smartphone

It serves as a holding tool for the back of the case. No hot air gun is needed with this equipment. Since it refers to methods that have a certain share of the risk of breaking Samsung with a high temperature.

Procedure:

In the middle there is a niche for a telephone. The body is placed between two rubber holders of the vice;
The cover of the device closes and the suction cup is activated. It is attached to the back of a Samsung smartphone. The joints must be moistened with alcohol or an alcohol-containing solution;
Attaching the Suction Cup to the Back Cover of a Samsung Smartphone
The pressure regulator, which is located on the right, comes into play. When tightening it, the smartphone body is held by a rubber vise, and the suction cup "pulls" up;
Pressure regulator in fixture
The adjuster is hand-tightened, but does not tighten tightly as we are dealing with a fragile material. We tighten the regulator every few minutes.
Samsung smartphone open case
Ultimately, the glue between the parts of the case gives in and the device is disassembled into two main parts - the back cover and mobile module Samsung phone ... When the cover comes off the module, you do not need to immediately open the fixture. It is necessary to remove the suction cup from the body, after which the machine can be opened.
Removing the cover with improvised tools on the Samsung Galaxy S9
More popular model Samsung Galaxy S9 practically does not differ in the process of disassembling the case from other models. Here, everything is also glued together, the engineers at Samsung decided. But we will consider manual disassembly of the device, without any special tools. We will use improvised means that are in every home. For example, instead of a hot air gun, you can use a regular hair dryer to dry your hair. But use it to its fullest. Direct the hot air flow only at the joints of the case.
It is necessary to warm up the glued joints with a hairdryer for a few minutes. A suction cup is also required to safely remove the back cover.
Samsung lid opening tools
It can be purchased at any children's store. Large suction cups are in priority - the more the back cover area is covered, the stronger the suction cup will hold it... We also need guitar picks ( plastic plates in the shape of a triangle) or plastic cards. Use two to support the already uncovered body parts.
Procedure:

In this article, we will tell you how to disassemble Samsung Galaxy S6. New smartphone is made in a case with a non-removable battery, so this operation will not be so simple.

Immediately, we note that if you decide to disassemble the Samsung Galaxy S6 on your own, then you automatically lose the warranty. Also, you need to prepare for the fact that there is a lot of glue inside the smartphone, and in some instances - especially a lot. Unfortunately, this approach to assembly is quite traditional for Asian manufacturers.

We also note that the disassembly of the Samsung Galaxy S6 Edge does not differ from the disassembly of the regular Galaxy S6, so further we will consider the disassembly process using this example.

Why would a Samsung Galaxy S6 disassemble be required? For example, for self-replacement of the battery, which is now non-removable.

Removing the back cover is easy enough, for this you need to pry it off the edges with a screwdriver or, much better, a plastic pick, and walk along the perimeter of the cover. Some people recommend preheating the back cover or removing it using a special suction cup.

As we can see, there is a lot of glue here.

Carefully separate the cover completely.

The display and the metal frame of the Samsung Galaxy S6 are connected with 13 screws, which are removed with a thin Phillips screwdriver (thanks not to a hexagon or some other perversion). After the screws have been unscrewed, the screen can be gently picked up and removed from the grooves of the frame.

Now comes the fun part. On the Samsung Galaxy S6, the board is attached to the display, not to the frame. Which creates, for example, when removing the battery, additional difficulties. Motherboard removed after disconnecting the antenna wires.

Now you can remove the battery (!). Why not at the beginning is a proprietary riddle from Samsung.

You can now remove Touch ID.

Now you can detach the glass from the display. In a number of sources, it is again recommended to preheat it.

Max Lubin

In the comments to many previous articles about smartphone repair, you asked the question of how to disassemble waterproof Samsung smartphones Galaxy S series to replace the back cover, and how difficult it is. Today I will try to describe this process in detail, indicating the nuances and possible pitfalls that may arise during the parsing process.

Given the abundance of glass in the structure modern phones, the most common reason for parsing is not the need to repair the electronics, but the banal replacement of the back cover, which often breaks when the phone is dropped.

Looking ahead, I can reassure the owners of the Galaxy S7 / 8/9 that even with a broken back cover and a broken protective glass display, your phone is most likely water resistant thanks to the laminate on the inside of the glass. This is clearly visible after removing this very cover. The film is surprisingly strong, and even shards of broken glass can rarely damage the film. This is a very big advantage of Samsung phones.

If, in spite of this, the rear cover needs to be replaced, a new one must be selected. Therefore, we will start not with the analysis itself, but with the choice of the back cover, which can be of very different quality, ranging from very inexpensive plastic ones to very expensive 100% original ones.

The easiest way to buy an original cover is to find an ad on Avito or Yulia selling the model you need for parsing. In this case, you will receive, although used, but the original cover, the quality of which will be noticeable better than analogues... How much it might cost is hard to say. It depends on the seller's appetite. Approximately for such a cover they ask from 500 to 1,000 rubles.

Another option is to order from online platforms such as AliExpress or eBay. In the first case, you will most likely get an analogue, the quality of which can range from excellent to terrible. In the case of eBay, it is better to look at the lots of sellers located in the United States, but then you will have to use the services of an intermediary, which will increase the purchase price. On average, it will be possible to keep within 1,000-1,500 rubles.

You can buy a spare part in the "store around the corner" for 300-500 rubles. The advantage of such a purchase is the ability to assess the quality and appearance before giving the money. The downside is that, most likely, it will turn out to be the same Chinese spare part.

There is one more, the most uneconomical option - buying the original from the official service centers(if sold). The cost of such pleasure can go up to 3,500-4,500 rubles. If you are a perfectionist, then this is your option.

After we bought the spare part, it's time to start disassembling our patient.

From the tools we need:

Plastic splitters. Guitar picks or even dense plastic packaging from something are perfect for this role.
Sucker. It is highly desirable to have it for these purposes. The usual plumbing is also suitable.
Wide tape
Rubbing alcohol or isopropyl alcohol. A syringe or jar with a spout as a container. It is more convenient for me to use a jar of hydrogen peroxide, since it is easier to control the dose with it 🙂
Ordinary household hair dryer as a heating tool. By the way, instead of a hair dryer, you can use a canvas bag filled with salt, preheated in a pan to 90 degrees. This option is preferable to a hair dryer, as it will allow the smartphone to warm up better and more evenly, which means that it will soften the adhesive tape holding the lid more.
Construction gloves to protect your hands from scalding (the phone will be hot).

Once everything is ready, it's time to get started.

We turn off the phone and proceed.

First you need to roll up the broken back cover in duct tape. This is necessary so that when parsing glass fragments do not remain on your fingers and do not fly into your eyes.

If you disassemble the phone not to replace the cover and at the time of disassembly the cover is intact, then you still need to glue it - it's not a fact that you will be able to open the phone without splitting the cover.

Please note that it is necessary to glue the lid with tape as carefully as possible, preferably without bubbles, and most importantly, without jams and joints. Otherwise, the suction cup will not stick to the lid, and it will become more difficult to open the phone.

Then we heat the phone with a hairdryer or a bag of heated salt.

When the phone is warmed up (so that it is difficult to touch it with your bare hand), glue the suction cup closer to one of the lower corners.

Then we drip alcohol into the joint between the lid and the case and begin to pull the lid off by the suction cup, while trying to push a pick or a plastic strip into the gap between the case and the lid.

If you open a whole lid, be very careful at this stage and do not try to push the pick too deep, as the voltage is too great and the lid can easily burst.

Never use a metal tool for this purpose, otherwise you will almost certainly split the lid.

The most important thing is to achieve the appearance of a small gap between the lid and the body. This may require several approaches of warming up, dripping alcohol and pulling back the lid by the suction cup. If the lid is already broken and the purpose of disassembly is to replace it, then you don't have to worry too much - pull harder and try to push the pick inside.

Alcohol in this case is needed to make the adhesive tape easier to stick off surfaces. Also, the alcohol will prevent the tape from grabbing back. Don’t pour too much, but don’t worry too much - alcohol will not harm the insides of the phone. The optimal dose is three / five large drops per joint.

After the lid opens slightly, we continue to drip alcohol into the joint and go around the entire perimeter, peeling off the tape. Take your time and remember to warm the lid where you peel it off.

An important caveat - do not push the connector deep inside in the middle of the right edge. There, very close to the edge, the outer turns of the coil pass. wireless charging, and there is a danger of damaging them.

Please note that in addition to the adhesive tape around the perimeter, sticky white seals are glued inside the lid, which must be saved. After the old cover is removed, you need to carefully re-glue the seals either on the new cover or on the inside of the phone in the same position as on the old cover. This will prevent the new cover from sagging and make the structure more assembled and tighter.

Then it is necessary to peel off the block of protective glasses of the camera and sensors from the old cover.

The glasses are in an aluminum frame, which bends very easily, so before peeling it off, warm it up well and remove it carefully. This frame is glued to a ring of scotch tape on a dense basis.

It is best to peel off with a flat thin tool. I am using a blade.

Once you've prepared your new cover for installation, it's time to get it clean. Namely - to clean the perimeter of the metal frame from the remaining adhesive tape, on which you will glue the new cover. Cotton buds and alcohol will help us with this. We slowly clean the frame, achieving absolute cleanliness, without lumps of old glue and tape. This is especially important if you want to maintain water resistance.

If protection from water is not important, then we take the lid, align it with the body and, gently pressing along the perimeter, glue it in place.

If you need to restore protection from water, then, in addition to the scotch tape, which is likely to be on the new lid, it will be necessary to glue the lid around the perimeter with glue or sealant. I recommend glue, as the sealant will take a very long time to dry in an enclosed space without oxygen.

After the lid is glued, you need to put it under the oppression for a couple of hours. Do not overdo it. A large book is enough.

That's all, our phone is ready. It remains to remove from the table, and you can use the new thing.

Conclusion

In this case, I specifically showed as an example an inexpensive Chinese cover, which can be bought in most spare parts stores, and which will most likely come to you from AliExpress. The color difference with the original is striking.

Therefore, it is worth considering whether this option suits you. If you are not satisfied, then you should look for other options, which I wrote about at the beginning.

Pay attention to the color of the tape in the original and in the Chinese. This is the easiest way to distinguish an original from a fake - in the original there is scotch tape, it is a thick white tape with neat edges. If the tape is of a different color, this is a fake or analogue, which can also be good, but less often.

As you can see, if you do not rush, then with the proper skill and patience, opening such a device turns out to be a simple and exciting task that you can do at home.

HTC flagship

The smartphone has an original design, its thickness is less than a centimeter, its height is about 15 cm. Such a phone is chosen by successful people, for whom their device is not just a phone, but a piggy bank of information: photos, important notes, music, documents and applications.

Xiaomi phones themselves are a little different from the standards we are used to. Since SIM cards are inserted from the side, it is not that easy to remove the back cover of your phone.

Yes, you can use a special needle, but it only helps to get the card slot in some Hiomi phones. Further, it is better to stock up on a mediator, and if it is not there, in this case any plastic card will help, it must be inserted between the case and the back cover (where the charging connector is), then all the latches must be snapped off along the perimeter:

Another way that you can open the back cover of your Xiaomi phone is with any suction cup that you have at home (even from a dash cam):

In order not to damage anything and safely open the cover of the Xiaomi smartphone, you need to use a special needle for such purposes, it comes with the kit and looks like this.

Now many smartphones open with such a thing, you can't remove a SIM from an Iphone without such a device. Just do not do as I do, do not take an ordinary sewing needle to open, then the phone will "junk" a little. I opened a SIM card on an Apple device with a needle, now the SIM card often fails.

How to open the back cover on a Xiaomi smartphone?

A feature of Xiaomi phones is that it will be problematic to remove the back cover yourself, although most smartphones currently have the same feature.

You can remove the cover, but I would not remove it at home, it is better to do this procedure in services, since you will need special equipment and experience in such work. If you want to take a chance, you can open the lid with a special spatula.

If you want to open the SIM card tray, then you can use the tool that comes with this smartphone.

Below is a photo of this tool in response.

Indeed, on smartphone Xiaomi the back cover is not easy to open.

But if you need to open the back cover, then you can use a special needle (which comes with the smartphone), it is just for this purpose, so that you can open the cover.

You need to act very carefully, pry a special hole with a needle and open it.

This is what this device looks like, with which you can open the back cover.

Well, why "no how!" - after all, it was somehow assembled at the factory (or maybe in the basement)

If you just need to open the back cover of your Xiaomi Redmi (Xiaomi) or Mi Max phone, and not just insert a SIM card, then this is done very carefully. To begin with, we pull out the tray for this very SIM card, otherwise it will interfere with disassembly. Now, using a special spatula, it is necessary, starting from one corner of the screen, to slowly move the cast cover, from the latches, and so we pass smoothly along the entire perimeter, without creases and distortions. After you have passed the spatula into the circular one, gently lift the back cover and detach the cable connecting the back cover and the front panel. That's how he understands.

The Xiaomi phone differs from others in its single body, so it is not possible to open the back cover.

In order to open the tray for changing the SIM card, you need to use a special needle that comes with the phone. It is necessary to press on the side of the phone case into a special hole and a tray with an extraction SIM card.

In this model, there is no need to remove the battery, as it does not block access to the SIM card slots.

I myself use a phone of this model, I used to think how to not be able to extract it battery(we got too used to extracting it), but now I don’t understand why we need to extract it. If the phone is good, with a capacitive battery, then the battery will not overheat and you do not need to remove it.

Of course, if you wish, you can open it using a sharp nail file, but it is better not to do this.

You can certainly try to open the back cover (like me), for this a female iron nail file is suitable, thin, forged latches, but Xiaomi phone you can damage or scratch, but not a fact, I opened it and nothing happened to it, I did the manipulations I needed, but the lid was difficult to open, and I do not recommend this method.

How to open the lid on Samsung Galaxy A3?

The modern mobile phone was created to simplify our life. In practice, however, difficulties may arise.

So, some device users note that not all phones are comfortable to use or not as advanced as their predecessors.

Therefore, this annotation will be needed for you if you do not understand how to open the cover on Samsung Galaxy A3.

After all, it becomes so unpleasant when you do not understand how to open the back cover, and close, as luck would have it, there is no one who can give you a hint or help.

But everything is not so sad, and at the moment you will find out how, in this case, you need to properly handle the Samsung Galaxy A3.

Difficult task for many

If you ask the majority of users the question: "How to remove the cover on the Samsung A3?", Then they will not be able to answer anything.

It seems that the company-developer decided that in order to perform such an act, we must contact the centers service phones.

In the centers, specialists will do it simply and quickly. After all, for this they have a set of special tools: a "spatula" (a device that disconnects the mounts) and a Phillips screwdriver.

But what if you do not have the ability to contact specialists or you simply do not have enough time to visit the service center? There is only one way out - to independently remove the back cover from the Galaxy A3.

Review SAMSUNG Galaxy A3 | mobilnika.net

| mobilnika.net

Prices on SAMSUNG Galaxy A3 - Review of the latest stylish model from SAMSUNG .

How it's done

It is important not to use brute force when disassembling a smartphone. Otherwise, it can lead to negative consequences: most likely, the smartphone will not perform its functions.

Also, dents, scratches or other damage may appear on the device's case, interfering with its normal operation and pretty spoiling its appearance.

Therefore, disassembling the Samsung A3, strictly follow the instructions below.

Find where the speaker of your smartphone is.
You will see a small notch (crack) above the speaker (from the end). With its help, the cover is removed.
Do not lift the cover up abruptly, otherwise you may damage the back panel. You can just push it up with your fingernail and gently pull it away from the device. Do not worry - it will not break. Never use sharp objects!

The back cover is open!

How to open the cover of Samsung Galaxy A3 and Galaxy A3 mini

To open the lid, specialists, in addition to the above tools, use a specialized hair dryer to warm it up.

It is quite difficult to do such a procedure at home. After all, you have to warm up the edges around the perimeter in the smartphone.

The phone is monolithic, so it is important to warm it up at a temperature of no more than 150 degrees (use a regular hair dryer for this).

After warming up, it is enough to gently pry off the cover with a plastic sharpened card, snapping off the screen from the case. Everyone - access to the internal modules is open!

If your goal is to completely disassemble the phone, then you must carefully read the instructions for complete disassembly. Replacing the cover is also easy - follow the steps in the opposite order.

If you know any other ways on how to remove the cover from Samsung Galaxy A3, share them in the comments. If you have any questions - ask, I will be happy to answer everything.

For many smartphone owners, BQ Strike has become a real problem with the question of how to remove the back cover of the device. Those who have never manually removed the back panel do not understand how to do it correctly and accurately without damaging the plastic or the display, and try to use various tools at hand, such as scissors, credit cards or knives. But don't do that - removing the cover on the BQ 5020 Strike is as easy as shelling pears with my own hands... Today we will tell you how to do it correctly. Also watch the tutorial video at the end of the article.

Why do I need to open my smartphone

The simplest and most important reason is to install a SIM card in a new gadget you just bought, as well as to install or replace an SD memory card, which is provided in almost every Strike BQs phone. Micro-SD card expands the capacity internal memory another 128 GB, which is undoubtedly a plus.

Many smartphone owners reboot a frozen device by pulling out and reinstalling the gadget battery. Also, the user may need to open the cover to replace an outdated or non-working battery with a new one. In addition, if you started to repair yourself or replace parts in a gadget, you cannot get close to the insides of the phone without removing the back panel.

So let's take a look detailed algorithm actions with which you can open the BQ phone and see what is inside it.

Algorithm of actions

First, inspect your smartphone. On its upper end, to the right of the micro-USB connector, you will see a small notch, as if created so that the cover can be pry off. Gently insert your fingernail into this recess and slide it to the left, going over the part where the plastic case fits snugly against the glass of the smartphone display. If you fail to do this, in the process of moving along the case with your free hand, slightly squeeze it on the sides so that the plastic bends and makes it possible to perform actions to open the lid. Next, gently run your fingernail around the entire perimeter of the smartphone several times, thereby opening the lid of the device. The plastic panel may crackle slightly when opened, and you shouldn't worry - this is normal. Open the lid of the BQs 5020 Strike once, and in the future you can easily do this operation over and over again.

How to close the lid back

It's even easier here - you don't even need your nails. Take your smartphone and place it in the plastic case. Make sure that all elements such as buttons and camera line up with the slots on the cover. Slightly press the phone to the body and walk in this way around its entire perimeter. You will hear characteristic clicks. Ready! Now you know how to open the lid of your BQ smartphone without damaging the case and screen. If something is not clear - watch a special training video.

Watch the video: Trailer of the play "The Master's Notes" (February 2020).

Required tools and screwdrivers to disassemble Samsung Galaxy S6 Edge:

Plastic spatula and pick
Suction cup for removing the display
Regular hairdryer

On our website you can buy the necessary set of screwdrivers for disassembling the Samsung Galaxy S6 Edge.

If you are starting to disassemble your smartphone for the first time, we recommend that you pay attention to the article "". This article provides guidelines to help you avoid typical mistakes in the process of disassembly and repair.

In this repair guide, I will show you how to disassemble and replace the back cover of Samsung Galaxy S6 Edge by yourself. This repair can help if your back cover is broken or cracked, or you want a new color.

Remember to switch off your phone and then remove the SIM card before starting repairs.

The very first step is to remove the back cover. Rear part The Samsung Galaxy S6 Edge case is firmly glued, so in order to remove it, warm up the phone around the perimeter using a regular hair dryer. Next, place the suction cup closer to the edge of the phone and pull it up. Place a plastic pick or the flat edge of a metal spatula into the resulting hole, and do the same on the other side of the phone. Next, run your pick around the perimeter of the lid to peel off all sides of the back cover. Warm up the glue again if necessary. As soon as all sides come off, you can remove the cover.

Installing the back cover and reassembling the Samsung Galaxy S6 Edge

Now attach the new back cover in place. Old glue is usually still quite sticky. Reattach the back cover, heat it slightly, and then press down on the cover with your hands or a couple of books.

Much to the delight of many Samsung fans, the new flagship Galaxy S6 received a completely monolithic body without a removable cover. This made it possible to make the design even more reliable, eliminate any backlash, and the design only won. However, this solution also has a significant drawback in the form of lack of access to the battery. However, as it turned out, it is still possible to replace the battery if necessary.

One of the users of the popular developer forum XDA Developers I found out that in the Galaxy S6 manual, the manufacturer superficially described the process of disassembling the case and removing the battery. True, this is far from being as easy as in the case of the previous models of the line. This will require:

remove the SIM card tray from the device;

remove the back panel;

loosen and remove the screws around the device;

remove the fee;

disconnect the battery connector;

remove the battery.

For more information on the instructions, you can refer to the Galaxy S6 manual (page 138) on the official Samsung website. The manufacturer himself strongly recommends not to engage in such operations on your own, the sequence of actions is described exclusively for authorized service centers, which must replace batteries and other hardware modules.

We join in this caution, as the process is indeed quite complex, and one incorrect action can void the warranty. In any case, all actions are performed solely at your own peril and risk.

Hello dear readers. Today, together with you, we will learn how to disassemble Samsung Galaxy S6 on our own, without the help of a specialist. Because this model the Korean smartphone does not have a removable back cover, at first glance it may seem that it is not so easy to disassemble it. However, you can handle everything with us!

It is important to understand, the initiative to disassemble the Samsung S6 deprives you of warranty service... Therefore, before disassembling it, weigh the pros and cons.

So, get ready for the fact that when you remove the back panel, you will see a copious amount of glue around its edges, this is one of the distinctive features of Korean manufacturers. By the way, since parsing a Samsung Galaxy S6 is no different from parsing a regular Galaxy S6, we will demonstrate the whole process on it.

Most often, the Samsung S6 needs to be disassembled to change the battery, due to its problematic availability. To do this, you need to use plastic tools so as not to damage the insides of the Galaxy S6, a common example is a regular plastic card.

Experienced craftsmen have in their arsenal different chips for disassembling smarts, we recommend prying the back cover with the same credit card. The cover will give in more easily if you preheat the phone with a stream of warm air from its side, so the glue will melt a little.

First step

This whitest film around the edges is the glue, as they said, there is plenty of it here.

Second step

Smoothly, without sudden movements, remove the back panel.

Third step

The S6 Edge's screen and metal body sit well on small screws that need to be removed with a small Phillips screwdriver. Then, when there are no screws left that hold the screen, it can be removed from the case.

Fourth step

As we can see, the motherboard is not attached to the Galaxy S6 case, but to its screen. Therefore, we remove it only after disconnecting the antenna wires.